phonelogo+234 8146561114 or +2347015391124
DESIGN AND CONSTRUCTION OF A MICROCONTROLLER BASED POWER THEFT IDENTIFIER

USER'S INSTRUCTIONS: The project work you are about to view is on "design and construction of a microcontroller based power theft identifier". Please, sit back and study the below research material carefully. This project topic "design and construction of a microcontroller based power theft identifier" have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this "design and construction of a microcontroller based power theft identifier" project research material is to reduce the stress of moving from one school library to another all in the name of searching for "design and construction of a microcontroller based power theft identifier" research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.


TITLE PAGE

DESIGN AND CONSTRUCTION OF A MICROCONTROLLER BASED POWER THEFT IDENTIFIER

BY

---
EE/H2013/01430
DEPARTMENT OF ----
SCHOOL OF ---
INSTITUTE OF ---

DECEMBER,2018



APPROVAL PAGE

This is to certify that the research work, "design and construction of a microcontroller based power theft identifier" by ---, Reg. No. EE/H2007/01430 submitted in partial fulfillment of the requirement award of a Higher National Diploma on --- has been approved.

By
---                                                     . ---
Supervisor                                                  Head of Department.
Signature……………….                           Signature……………….        

……………………………….
---
External Invigilator



DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.



ACKNOWLEDGEMENT

The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.


PROJECT DESCRIPTION: This work "design and construction of a microcontroller based power theft identifier" research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of "design and construction of a microcontroller based power theft identifier" visible for everyone, then the complete material on "design and construction of a microcontroller based power theft identifier" is to be ordered for. Happy viewing!!!


ABSTRACT

The present thesis, Microcontroller Based Power Theft Identifier, introduces the concept of preventing the illegal usage of the electrical power. Here, the radio communication principles are employed and also the technology of Microcontrollers is utilized to find out the user trying for pilferage of power i.e., by displaying the respective consumer meter number and address.
For the complete operation, the system can be sub-divided into two major sections, one is the transmitting section and the other is the receiving section. The transmitting section has to be incorporated at the consumer’s end and the receiver section has to be placed at the electrical sub-station.
In the transmitting section, two types of automatic power theft detection schemes are provided. In the first scheme, within the meter (inside the bottom cover), an electro-optical sensor is placed and it is configured to feed trigger signal for the timer circuit. Whenever light falls on it (when user tries to open the bottom cover), the output of the timer circuit energizes a relay which provides supply for modulating input section which differs from user to user.
The GSM module used Microcontroller identifies theft when it occur, the frequency and its associated user. Then it energizes an alarm and displays the address of the user to the power holding company ( PHCN). 

TABLE OF CONTENTS
COVER PAGE
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT
CHAPTER ONE
INTRODUCTION
1.1      BACKGROUND OF THE PROJECT

    • PROBLEM STATEMENT
    • AIM/OBJECTIVE OF THE PROJECT
    • SIGNIFICANCE OF THE PROJECT
    • SCOPE OF THE PROJECT
    • ADVANTAGES OF THE PROJECT
    • LIMITATIONS OF THE PROJECT
    • APPLICATIONS OF THE PROJECT
    • METHODOLOGY
    • PROJECT ORGANISATION

CHAPTER TWO
LITERATURE REVIEW

    • OVERVIEW OF ELECTRICITY THEFT
    • DIFFERENT TYPES OF ILLEGAL ELECTRICITY THEFT
    • CAUSES OF ELECTRICITY THEFT
    • EXISTING WAYS OF TACKLING ELECTRICITY THEFT
    • MERITS OF PROPOSED METHODOLOGY
    • HISTORICAL BACKGROUND OF ELECTRICAL POWER THEFT
    • REVIEW OF RELATED STUDIES

CHAPTER THREE
METHODOLOGY

    • SYSTEM DESIGN
    • COMPOSITION OF HARDWARE
    • WORKING OPERATION
    • SYSTEM BLOCK DIAGRAM
    • POWER SUPPLY CIRCUIT CONNECTION
    • CIRCUIT EXPLANATION
    • MATHEMATICAL MODEL OF THE SYSTEM
    • PROGRAMMING LANGUAGE AND SIMULATION SOFTWARE UTILIZED

       
CHAPTER FOUR
RESULT ANALYSIS

    • RESULTS AND DISCUSSION

CHAPTER FIVE

    • CONCLUSION
    • RECOMMENDATION
    • REFERENCES

CHAPTER ONE

1.0                                                      INTRODUCTION

The proposed project work aims on the design and development of energy theft prevention aspect. Thereby, energy pilferage can be reduced to a considerable extent. This project envisages the development of energy theft identification. Hence this project work is titled as “MICROCONTROLLER BASED POWER THEFT IDENTIFIER”.
Meters in the past and today in a few countries, were electromechanical devices with poor accuracy and lack of configurability. The present billing system is minimally able to detect power theft and even when it does that it is at the month. The distribution company is unable to keep track of the changing maximum demand for the domestic consumer while the consumer is faced with problems like receiving due bills for bills paid for and also poor reliability of electricity supply and quality [1]. Prior to the introduction of prepaid meter, various methods were proposed to detect electricity theft which includes: inspection of suspicious load profile, though the method was good certain drawbacks accruing to this method are the requirement of large manpower and huge labour, this failed due to dishonesty of the service workers. A huge amount of money is lost due to theft, in some countries; the government has to provide subsidies to the power sector to maintain a reasonable price of electricity [2]. The major problem facing the electricity industry in many developing countries is poor revenue generation. This arises from illegal consumption of electricity via mostly meter tampering and bypassing as well as direct connection to the low voltage distribution lines. In order to solve all the problems of the traditional meter reading, the consumer load should be tracked on a regular basis as this will help ensure accurate billing, keep track of the maximum demand and detect theft. In this work a GSM is used here to send message to power holding company whenever the power detected theft.

1.1                                       BACKGROUND OF THE STUDY

Science and technology with all its miraculous advancements has fascinated human life to a great extent that imagining a world without these innovations is hardly possible. While technology is on the raising slope, we should also note the increasing immoral activities. With a technical view, "Power Theft" is a non-ignorable crime that is highly prevalent, and at the same time it directly affects the economy of a nation.
Electricity is the modern man's most convenient and useful form of energy without which the present social infrastructure would not be feasible. The increase in per capita production is the reflection of the increase in the living standard of people. When importance of electricity is on the increasing side, then how much should theft of this energy or illegal consumption of power from the transmission lines be averted?
Power theft has become a great challenge to the electricity board. The dailies report that Electricity Board suffers a total loss of 8 % in revenue due to power theft every year, which has to controlled. Our paper identifies the Power theft and indicates it to the Electricity board through Power line. We had also dealt about the remote monitoring of an energy meter.

1.3                                   PROBLEM STATEMENT
Theft of electricity is an illegal means of using electrical power. It belongs to the non-technical losses. Non-technical loss (NTL) during transmission of electrical energy is a major problem in developing countries and it has been very difficult for the utility companies to detect and fight the people responsible for theft. Electricity theft forms a major chunk of NTL. These losses affect quality of supply, increase load on the generating station, and affect tariff imposed on genuine customers. This work solves the problem of consumers stealing electricity which causes loss of revenue.

1.3                                    AIM OF THE PROJECT
The main aim of this work is to identify the Power theft and indicates it to the Electricity board through Power line. In this work a GSM is used here to send message to power holding company whenever the power detected theft.

1.4                          SIGNIFICANCE OF THE PROJECT
This device detects illegal use of electricity thereby increasing country’s revenue. We had also dealt about the remote monitoring of an energy meter using GSM. With the implementation of this kind of systems in the real time, the need for regular vigilance can be avoided and power can be supplied at the economical rates, thereby improving the economy of the country.

1.5                                  SCOPE OF THE PROJECT
This paper proposes an architectural design of smart meter, external control station, and harmonic generator. Motivation of this work is to deject illegal consumers, and conserve and effectively utilize energy. As well, smart meters are designed to provide data of various parameters related to instantaneous power consumption. NTL in the distribution feeder is computed by external control station from the sending end information of the distribution feeder. If a considerable amount of NTL is detected, harmonic generator is operated at that feeder for introducing additional harmonic component for destroying appliances of the illegal consumers. For illustration, cost–benefit analysis for implementation of the proposed system in India is presented. This work is GSM based power theft identifier. The GSM is used for remote monitoring of the meter reading and sending SMS whenever there is abnormal readings in the customer electricity meter

1.6                           ADVANTAGES OF THE PROJECT

  • The system consumes very little power for its operation.
  • System operation is independent of time (24 hours functioning).
  • Automatic user identification.

1.7                           LIMITATIONS OF THE PROJECT

  • Since the techniques employed in this module are based on simple electronics, the chances of making the system inoperative are more. But, if a Microcontroller chip is used for feeding the modulating input, we can make the system more efficient.
  • Wide range of frequencies is required to facilitate large number of users. To overcome this, carrier levels can be changed from region to region.
  • Presently, it requires a power supply (230 V) for the operation, but a small battery with automatic charging facility can be provided in real time.

1.8                          APPLICATIONS OF THE PROJECT

  • The system can be incorporated for almost all types of users.
  • The concept is well suited especially for villages and interior areas.

1.9                                         METHODOLOGY
To achieve the aim and objectives of this work, the following are the steps involved:

  • Study of the previous work on the project so as to improve it efficiency.
  • Draw a block diagram.
  • Test for continuity of components and devices,
  • programming of microcontroller
  • Design and calculation for the changeover was carried out.
  • Studying of various component used in circuit.
  • Construct a digital changeover circuit.
  • Finally, the whole device was cased and final test was carried out.

1.10                                                      PROJECT ORGANISATION
The work is organized as follows: chapter one discuses the introductory part of the work,   chapter two presents the literature review of the study,  chapter three describes the methods applied,  chapter four discusses the results of the work, chapter five summarizes the research outcomes and the recommendations.


CHAPTER TWO: The chapter one of this work has been displayed above. The complete chapter two of "design and construction of a microcontroller based power theft identifier" is also available. Order full work to download. Chapter two of "design and construction of a microcontroller based power theft identifier" consists of the literature review. In this chapter all the related work on "design and construction of a microcontroller based power theft identifier" was reviewed.

CHAPTER THREE: The complete chapter three of "design and construction of a microcontroller based power theft identifier" is available. Order full work to download. Chapter three of "design and construction of a microcontroller based power theft identifier" consists of the methodology. In this chapter all the method used in carrying out this work was discussed.

CHAPTER FOUR: The complete chapter four of "design and construction of a microcontroller based power theft identifier" is available. Order full work to download. Chapter four of "design and construction of a microcontroller based power theft identifier" consists of all the test conducted during the work and the result gotten after the whole work

CHAPTER FIVE: The complete chapter five of design and construction of a "design and construction of a microcontroller based power theft identifier" is available. Order full work to download. Chapter five of "design and construction of a microcontroller based power theft identifier" consist of conclusion, recommendation and references.

 

CLICK HERE FOR MORE RELATED TOPICS/MATERIAL


To "DOWNLOAD" the complete material on this particular topic above click "HERE"

Do you want our Bank Accounts? please click HERE

To view other related topics click HERE

To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE

Do you want us to research your new topic? if yes, click "HERE"

Do you have any question concerning our post/services? click HERE for answers to your questions


For more information contact us through any of the following means:

Mobile No phonelogo:+2348146561114 or +2347015391124 [Mr. Innocent]

Email address emailus:engr4project@gmail.com

Watsapp No whatsapp.html :+2348146561114


COUNTRIES THAT FOUND OUR SERVICES USEFUL

Australia, Botswana, Canada, Europe, Ghana, Ireland, India, Kenya, Liberia, Malaysia, Namibia, New Zealand, Nigeria, Pakistan, Philippines, Singapore, Sierra Leone, South Africa, Uganda, United States, United Kindom, Zambia, Zimbabwe, etc
Support: +234 8146561114 or +2347015391124

Watsapp Nowhatsapp.html
:+2348146561114


E
mail Address emailus:engr4project@gmail.com


FOLLOW / VISIT US VIA:

tweeter instagram.htmlfacebook logo

Order Full Material(s)
Download Full Material(s)
Bank Accounts

Contact us

Hire a writer

Order/learn construction


View other related topics

Vrequently asked questions(FAQ)
View more related topics and download more material
Format = microsoft word

Chapters = 1-5 chapters


Price: N3,000.
»Accountancy (AC) project
» Agric engineering project topics
» Business admin and management project
» Banking and finance project
» Civil engineering project
» Co-operative economics and management project
» Computer science project
» Community Health Project
» Electrical/electronic/telecom/ power project
» Estate management project
» Education
» Human Kinetics & Health Education Project
» Industrial safety and environmental (ISET) project
» Mass communication project
» Mechanical engineering (ME) project
» Medical And Health Science Project
» Office technology and management (O.T.M) project
» Public administration (PA) project
» Public Health Education Project Topics
» Paramedic Project Topics
» Industrial Physics/Physics Electronics Project
» Science laboratory technology (microbiology option) project
» Agricultural science and engineering seminar
» Building engineering seminar topics/materials
» Civil engineering seminar topics
» Computer science seminar topics
» Environmental seminar topics
» Electrical/electronic/telecom/ power seminar
» Mechanical engineering seminar
» Physics / industrial physics/physics electronics seminar topics/materials